The Aspire Flexus replacement coils are designed to fit into the Flexus pod as part of the Aspire Flexus kit.

No matter which one you choose, either of the coils will produce an authentic MTL (Mouth To Lung) inhale with a discreet amount of vapour. However, the 0.6 Ohm coil creates a little more vapour than the 1.0 Ohm version.

Features:

MTL Vaping
Mesh Build
Multiple Resistances
Compatible With High PG E-Liquid
The mesh lattice build featured in either coil means that your e-liquid heats up faster and delivers an improved flavour. If you’re using the 0.6 Ohm coil, we’d suggest that your kit is set to around 15 – 18W. Though if you’ve chosen the 1.0 Ohm version, we’d recommend that it’s vaped at around 12 – 15W instead. To match either coil, using an e-liquid with a 50/50 or high PG concentration will deliver the best results.

Contains:

5 x Aspire Flexus Replacement Coil

Uwell Caliburn G2 Replacement Coil is designed for Uwell Caliburn G2 Pod System Kit 750mah.

Uwell Caliburn G2 cartridge adopts Pro-FOCS flavour adjusting tech to provide you with original taste and pure flavour. Caliburn G2 is compatible with 1.0 Ω coil and 0.8 Ω coil of Caliburn G.

Parameters:
Resistance: FeCrAI UN2 Meshed-H 1.2ohm(9-13W)

Features:
Pro-FOCS flavour adjusting tech
MTL & restricted DTL vaping

Horizon Sakerz Coil is a mesh coil specially made for Sakerz Tank. There are two different mesh coils that will bring you a different vaping experience.

It has two options: 0.16ohm mesh coil for 70W, 0.17ohm 2in 1 mesh coil for 70W. The unique pressure installation design is easy to use. Only 4 steps: 1. Unscrew to remove the tank base; 2. Take out the used coil with a wrench;  3. Install a new coil by pressing the coil into the chamber;  4. Make sure All o-rings are fixed;  5. Screw the tank base back onto the tank.

Compatible with HorizonTech SAKERZ Tank

The Mesh Coils for TFV18 Tanks, 0.33ohm Single Mesh Coils, 0.15ohm Dual Mesh Coils, and RBA available.

The Mesh Coils with single or dual mesh wire inside, which will enlarge the contact area with the e-juice, will heat the juice fastly and evenly, the Single Mesh Coil with the tighten contact with the cotton inside, will bring the mellow flavor, best rated at 100W to 110W.

The Dual Mesh Coil for optimized taste, accelerating heating for the dense vapor, best rated at 100W to 110W. the RBA core will provide DIY fun, supports dual coil building.

Features:

0.33ohm TFV18 Single Mesh Coil, 80-140W, Best: 100-110W
0.15ohm TFV18 Dual Mesh Coil, 80-140W, Best: 100-110W
TFV18 RBA Coil, Pre-installed 0.33ohm Coil, 45-80W, Best: 55-65W(1PC/Pack)
3PCS Per Pack
Fit For TFV18 Tank Only

Includes:

1*TFV18 Coils

A brand-new design for the TPP pod tank, as featured on the Drag 3 and Drag X Plus kits by Voopoo.

These DM coils come in a choice of two resistances:

– DM1 0.15ohm mesh coil, rated between 60-80W
– DM2 0.2ohm mesh coil, rated between 40-60W

These coils use established mesh technology to provide a purer flavour, and a superior vapour.

These coils are only compatible with the TPP Pod tank

The Uwell Crown 5 replacement coils have been designed for use with the Uwell Crown 5 vape tank and kits that feature it.

There are three varieties of this coil available, all of which have been designed to support sub ohm vaping and feature mesh builds to improve both flavour and vapour production. When it comes to e-liquid we recommend pairing them with a high VG e-liquid that is 70% VG or higher.

Features:

• Uwell Crown 5 Coils
• Designed For Sub Ohm Vaping
• Multiple Resistances
• Mesh Builds
• Compatible With High VG E-Liquid

The 0.2 Ohm Crown 5 coils feature the lowest resistance and rely on a triple mesh build to deliver the highest level of vapour production. Capable of being used between 65 – 70W these coils can be supported by a range of sub ohm vape devices.

The 0.3 Ohm Crown 5 coils, on the other hand, feature a dual mesh build and their slightly higher resistance are more suited to delivering a balance of flavour and vapour production. They can be used between 50 – 55W.

The 0.23 Ohm Crown 5 coils offer a mid-point between the two. They utilise a single mesh build that still delivers better flavour from e-liquids but produces slightly more vapour than the 0.2 Ohm coils. They can be used between 65 – 70W.

Important information about sub ohm vaping:

Any coil that registers below 1.0 Ohm, is known as a sub ohm coil. Recommended for advanced vapers only, they’ll require more power to use properly, which will be provided by a sub ohm vape kit.

With these coils larger amounts of vapour will be created, to support this we recommend you use e-liquids that are 60% VG or higher. Due to the larger amounts of vapour that is created, we advise that you do not use an e-liquid that has higher than a 6mg nicotine strength.

Uwell Caliburn G Coil is designed specifically for use with the Uwell Caliburn G Pod Kit.

The coils are available in two types resistances. With a 0.8ohm mesh coil and a standard 1.0ohm coil to choose from. Suitable for both mouth-to-lung and direct-to-lung vaping.

Replacing the coils is simple thanks to the pod’s plug and play design. Simply slide the old coil out of the base, press-fit the new coil from the bottom of the pod to install.

It is recommended to pair using the two coils with a high PG e-liquid with a PG content greater than or equal to 50% to achieve the best performance.

Stock up on Caliburn G Coils to always ensure a tasty vaping experience at a budget-friendly cost.

The new look Uwell Caliburn G represents a welcome improvement to an already terrific pod kit, one that offers more versatility and performance without sacrificing any of the original’s simplicity or discreet style.

Unlike the closed-coil system of the original pods, the Caliburn G pods can be fitted with a 0.8ohm replaceable coil for increased vapour.

Both coils work best with high-PG, 50/50 and nicotine salts eliquids.

Kroma-Z pods come with a side-fill port, so you don’t have to remove the pod from the device when you fill it.

The pods use interchangeable 510 drip tips, so you can customise the look of your pod with the drip tip of your choice.

The device comes with replaceable coils, which means the pod lasts longer as you can change the coil when it comes to the end of its life. It also means you can change your style of vaping by choosing a different coil resistance.

COMPATIBLE COILS

Innokin Kroma-Z pods work with Innokin Z coils. Two Z coils come with the pod, including a new 0.3 Ω Z coil which is suitable for restricted Direct-Lung vaping.

COIL RATINGS

0.3 Ω Z Coil: 30 – 40 W
0.8 Ω Z Coil: 15 – 18 W